Welding / arc-blow support
A fitted pipe joint
Use the pipe-weld procedure when magnetism is interfering with welding at the joint.
Open pipe-weld instructions Manual pages 6–7 ↗Canadian Degauss · Renter support
Before you power on,
start here.
Set up with confidence. Protect your cables. Find the right instructions for the job in front of you.
01
Choose the right procedure
What are you working on?
Pipe-end degaussing
A pipe end before welding
Use the pipe-end procedure for reducing residual magnetism at a pipe end. Its sequence differs from welding support.
Open pipe-end instructions Manual pages 8–10 ↗A different component, a second cable, or an unfamiliar setup? Call us to confirm your application.
02
Before operation
Five checks for a better setup.
Use these as preparation checks alongside the full manual. They are not a substitute for its operating sequence.
- Match the unit and the job.Identify your supplied equipment and choose the correct procedure above. Confirm unfamiliar controls or cable configurations with us.
- Inspect before energizing.Check cable jackets, connectors, cords and seals. Damaged insulation or exposed wires means stop and contact us.
- Plan the power supply.Use the supplied power cords and follow the manual’s source and GFCI instructions. Confirm generator suitability before use.
- Plan the wrap and cable protection.Follow the job-specific wrap arrangement. Account for hot pipe, welding debris and possible physical damage before laying out the cable. Confirm the insulation needed on preheated pipe.
- Plan how you will monitor heat.Confirm operating limits and how to assess cable heating for your rental. Make sure the operator knows when to stop and who to call.
Cable care is part of the job
Heat comes from two places.
Running the unit
Cables can heat while the equipment is operating. Longer operation requires continued attention to cable condition.
The pipe itself
Preheated or hot pipe can transfer heat to the cable jacket. Use the protection specified for the application.
Suspect overheating? Stop operation.
Follow shutdown and power-isolation instructions before handling or moving cables. Keep clear of hot surfaces and allow cooling. If there is damage, uncertainty about cable condition, or no confirmed operating guidance for the job, contact us before restarting.
Talk through your setup: 306-250-9294Feeling cool alone does not confirm that a cable is undamaged or ready to restart. This guide does not supply a universal run-time, cooldown period or temperature threshold.
03
Answers close at hand
The questions we hear in the field.
How should I wrap the cable for my job?
First choose your application below. For pipe-weld support, the manual specifies a snug cable fit. Pipe-end degaussing uses a different process and may use a fixed-diameter coil. Do not assume one arrangement suits both jobs. Use the instructions for your supplied unit and contact us if the wrap arrangement is unclear. Pipe-weld guidance: page 6 · Pipe-end guidance: page 8.
How do I protect the cable from hot pipe and welding debris?
Plan cable protection before energizing. The manual says to wrap over insulation on preheated pipe and describes positioning the cable away from the joint to protect its jacket from sparks, slag and welding debris. Confirm suitable insulation and placement with Canadian Degauss for your application; a cover is not a substitute for monitoring heat. Read the cable-protection notes on page 6.
Why are the cables getting hot?
The cables can heat during operation, and hot pipe adds another heat source. Monitor conditions throughout the job, not only during initial setup. If overheating is suspected, stop operation and follow the shutdown and isolation instructions before handling the equipment. Do not use bare-hand contact to test a potentially hot cable. Call us if you are unsure how to assess the condition.
How long can I run, and when can I restart?
There is no universal run/rest timer on this guide. The supplied manual does not state a general duty-cycle, maximum continuous run-time or cooldown limit. Confirm the appropriate operating limits and heat-assessment method for your unit and job with Canadian Degauss before use. If heating becomes a concern, stop and allow cooling; do not restart until the cause is addressed and safe operating conditions are confirmed. The brief timings in the pipe-end procedure are process steps, not a general thermal limit.
What should I inspect before use?
Read the warnings and inspect the supplied equipment. Look for damaged cable jackets, exposed wires, damaged connectors and damaged switch seals. Do not energize damaged equipment. Contact Canadian Degauss for support; only qualified personnel should service the equipment. Warnings: page 2 · Power box: page 3.
How do I avoid damaging the cable connectors?
Keep the dustcaps on while installing or transporting the cable. Align the keyed connectors as described in the manual and tighten the collar by hand only; do not use tools. Connectors must be clean and dry before energizing. Do not disconnect or reposition an energized cable. Connector instructions: page 5.
The unit will not power on. Where do I start?
Use the power-source and supplied-cord checks in the manual, including its instructions for the manual-reset GFCI. Do not bypass protection, repeatedly reset a fault, open the control panel or change wiring to make the unit run. If the prescribed setup does not resolve the issue, call Canadian Degauss. Power sources and GFCI: page 4.
Do I need a second cable?
That depends on the application and supplied configuration. Contact us before adding a cable or splitter. The manual has a separate second-cable procedure, including winding-direction guidance. Follow that complete procedure rather than improvising a connection. Second-cable instructions: page 11.
Keep it with the equipment
Take the guide to site.
Save the full manual and print this guide before leaving coverage. Printed copies include the setup checks, FAQs and support number.
The original manual QR still opens the same PDF. This new QR opens the renter guide.
canadiandegauss.ca/start
Scan before you start
A useful call starts with the right details
Still unsure about your setup?
Have your unit ID, pipe size, application, pipe condition and cable arrangement ready. Tell us what you have observed and what you have already checked.
Source: Industrial Degauss IDMAG System Instruction Manual, supplied with Canadian Degauss rentals. Additional cable-heat reminders from Canadian Degauss. Guide updated October 7, 2026.